{"id":8944,"date":"2009-07-28T06:06:07","date_gmt":"2009-07-28T10:06:07","guid":{"rendered":"http:\/\/www.woodworkersguide.com\/?p=1791"},"modified":"2016-01-25T23:30:21","modified_gmt":"2016-01-25T23:30:21","slug":"craftsman-style-end-tables-done","status":"publish","type":"post","link":"https:\/\/ravenview.com\/craftsman-style-end-tables-done\/","title":{"rendered":"Craftsman Style End Tables – Done!"},"content":{"rendered":"
Well, they’re finally done! The Craftsman Style End Tables that I started several months ago are finished. \ud83d\ude42<\/p>\n
It’s always a thrill starting a new project and equally as thrilling, no, even more so, when it is finished. Sometimes this is because you are just happy to be done with the project, other times it’s because you are happy with the project. In this case, I’m quite happy with the project. \ud83d\ude42<\/p>\n
The overall size of each of the tables is 20 1\/4″ wide X 24 3\/8″ deep X 24″ high and they make a great match for the Craftsman Style Coffee Table<\/a> made previously.<\/p>\n Although they took me several months to complete the actual time spent working on them was only between 40 and 50 hours. I worked at them periodically, interspersed between other projects. The pieces sat for a couple of months waiting for an opportune time to do the finishing which I knew would tie up the shop for a couple of weeks.<\/p>\n Here are some more photos of the finished tables:<\/p>\n <\/p>\n And here they are in their proper place in our home:<\/p>\n Here’s the cut list and a few notes for this project:<\/p>\n Table Top – 2 pieces at 20 1\/4″ X 24 3\/8″ All stock is 3\/4″ thick The stain I used was Flecto Varathane Golden Mahogany.<\/p>\n What have I learned, what would I do differently? Well, there are several things. <\/p>\n First, is to be more critical in the choice of wood, in respect to the grain, for different parts. I believe that with a bit more care I could have matched the grain in the legs better so that, at least for when viewing the front or backs (one of the tables is viewed from both sides), the grain would have been more symmetrical and looked quartered sawn.<\/p>\n Second, still working with symmetry and grain, I should have cut the front top and bottom stretchers and the drawer front from a single piece of wide board. This would have then flowed better as one piece.<\/p>\n Third, the drawers. I’m not completely pleased with them. As all drawers, they should have been dovetailed. When I graduate to a dovetail saw and become competent enough with it I hope to remake them\u2026 though probably never will, but the thought gets me through the day. \ud83d\ude42<\/p>\n However, even with these ‘criticisms’ I am quite pleased with the way the project turned out. I’m looking forward to starting the fourth and final piece for this set, the sofa table.<\/p>\n Back to the shop\u2026<\/p>\n
\nBottom Shelf – 2 pieces at 15 3\/4″ X 16 3\/4″
\nLegs – 32 pieces at 2 1\/8″ X 23 1\/4″
\nShort Stretchers – 6 pieces at 2 1\/4″ X 15 5\/8″
\nLong Stretchers – 8 pieces at 2 1\/4″ X 19 5\/8″
\nShort Stretchers (bottom of drawer) – 4 pieces of 2″ X 15 5\/8″
\nLong Stretchers (bottom of drawer) – 4 pieces of 2″ X 19 5\/8″
\nStretchers (top of drawer) – 2 pieces at 1″ X 15 5\/8″
\nSide Panels – 4 pieces at 5 1\/4″ X 19 5\/8″ X 3\/8″
\nBack Panels – 2 pieces at 5 1\/4″ X 15 5\/8″ X 3\/8″
\nSlats – 20 pieces at 10 1\/2″ X 1 1\/4″ X 1\/2″ (rough length)
\nDrawer Fronts – 2 pieces at 7″ X 16 1\/2″ (rough)
\nButtons (Sides) – 16 pieces at 2″ X 1 1\/4″<\/p>\n
\nTenons on stretchers are 1″
\nTenons on slats are 1\/2″
\nFrame sits in approximately 2″ from top edge
\nBottom stretchers are 3 1\/2″ from the floor
\nMortises for top are 1\/2″ from top and 1 1\/2″ long
\nSlats are 1 3\/8″ apart<\/p>\n